In paint can be found many substances: Eg. in Kaolin, which is extracted from Kaolinite, it is such. in Georgia in a big way.
Al2O3
SiO2
Fe2O3 (added to coverage / color)
TiO2 (also known as Titaniumwhiteninger)
CaO
MgO (in very small quantities)
Na2O (in fact, a pollution)
And many other substances but in very small quantities (Uranium, Thorium, Lead, Chromium, Potassium) (possibly from fly ash, which can also be mixed into the paint)
Pure Al powder (pigments) (ie elemental Al) is widely used in paints. Available at drugstore for exactly this, if you want to mix yourself.
The paint must be so tied together:
It may be cellulose, turpentine, but it can also be a mixture of 5-10% of the resin / rest turpentine, turpentine which evaporates in a short time.
The resin is returned, and it can only? dissolved by alcohol.
But not in a MEK solution, so far as I know.
Turpentine-based oil paints are not miscible with cellulose based paints, I do not know why.
But they burn well, even after they have dried up, with the vigorous development of black smoke.
Carsten:
You mentioned "cellulose paints", which could be used as other kind of paints in WTC, but I should refine this stuff and perhaps I should add first some general remarks as for solubility of linear (not cross-linked) polymers.
Like for other substances, the solubility of polymers keeps the old rule
"similia similibus solvuntur". We can divide polymers roughly into three categories, according to their "polarity", which is manifested e.g. by their dielectric constants.
-
Non-polar polymers like polystyrene, polyolefines, did not contain any organic polar groups like hydroxyls, acyls, amides, esters, carbonyls, etc. They contain only aliphatic and aromatic non-polar moieties. Therefore they are best dissolved in
non-polar solvents like toluene, fluorinated alkanes (polyolefines), but also in tetrahydrofuran (THF), which is just slightly polar solvent etc.
-
Polymers with moderate polarity like polymethylmethacrylate, polyvinylacetate or
esters of cellulose, with moderately polar groups like esters, carbonyls. Hence they dissolve best in
moderately polar solvents like e.g. acetone, MEK, chloroform, tetrahydrofuran, but also they are sometiimes soluble in polar aprotic solvents like dimethylformamide (DMF) of dimethylsulfoxide (DMS).
-
Polymers with high polarity like polyvinylalcohol, polyacryclic acid, polyacrylic acid sodium salt, or e.g.
linear cellulose, bearing highly polar e.g. hydroxyl groups, acyl groups or their salts. They are best soluble in
highly polar solvents like alcohols, acetonitrile, in polar aprotic DMF, DMS, but even in water sometimes (and in tetrahydrofuran).
I emphasize: all this deals with the solubility of linear polymers. Densely crosslinked polymers like epoxy in Laclede WTC primer can not be dissolved in any solvent, no matter how proper is this solvent as regards its polarity.(There are also other causes of polymer insolubility, like too strong interaction of aromatic groups in rather "exotic" conjugated polymers and "highly aromatic" polymers ("pi-stacking"), but this is out of the scope here).
Also, I can add one practical remark (after I have dissolved thousands of various polymers by myself
: by far the most universal, almost miraculous solvent for polymers is tetrahydrofuran: it dissolves many non-polar polymers as well as polar ones, including e.g. polyvinylchloride, which is otherwise soluble only in cyclohexanone.
And now back to
cellulose. In paints, not cellulose itsef is usually employed, but its esters are used:
nitrates of cellulose (nitrocellulose) or
acetates (butyrates) of cellulose. The solubility of these stuffs depends on the degree of esterification ("concentration" of nitrate or acetate groups). With this degree increasing, the solubility in highly polar alcohol(s) decreases, whereas solubility in moderately polar solvents like acetone or MEK increases. E.g., nitrocellulose is frequently dissolved not in alcohol itself, but in the mixture of ether and alcohol (this mixture is less polar), forming viscous solution called
collodion.
So we can not simply say: cellulose paint binders are soluble in alcohol(s) but not e.g. in acetone, the matter is much more complicated in fact
