Thus the question whether "heat rejection via radiative means is a third-order term" depends on temperature.
No. You don't understand what is meant by "the problem." The problem is the design of a heat shield. The solution involves several factors working in concert. Rejection of heat by radiative heat transfer is a third-order term in the quantitative solution. You're trying to claim the gaseous ablation products cannot be suitably opaque as I claimed because then the heat shield wouldn't be able to radiate away heat. That's a knee-jerk response based on what you desperately want to be true, not what is true.
In the textbook provoking this thread (
#1), the authors deal with three approaches to thermal-protection systems:
- Heat sinks
- Ablation
- Radiative cooling
If you are right and "radiative heat transfer is a third-order term in the quantitative solution" then thermal protection in case of Apollo must almost fully rely on ablation, since involved thermal energy is far too enormous for being relevantly absorbed by heat sinks of the reentry capsule (
#68).
But as Ive learned to expect no useful reply from wogoga I'll ask JayUtah: does the Orion/constellation stuff use substantially different technology for reentry shielding? The capsule is bigger, and designed for larger payloads up and down, does it still use slow-charring epoxy for an ablative reentry shield? I've not really followed the thing because it seems like NASA was designing a tool for a job that doesn't exist.
It's almost a carbon copy of Apollo's heat shield. No pun intended.
There is a huge difference between a heat shield losing roughly 100 kg of "slow-charring epoxy" and a heat shield losing e.g. 1000 kg carbon (
#196,
#336). Carbon has a
sublimation temperature of 3915°K and a
vaporization enthalpy of 355.8 KJ/mol
≈ 5p356 Joule per mole. Taking into account heat capacity, this results in a theoretical heat absorption capacity of more than 30 MJ/kg
= 7p3 Joule per kg. Thus, by vaporizing 1000 kg
= 3p1 kg, the heat shield can remove 30 GJ
= 10p3 Joule of reentry heat. This would already result in around 10%
= 9n1 = n1 of total heat of 330 Gigajoule
= 11p33 J emerging during an Apollo reentry (
#196).
And 3915°K also renders radiative cooling very effective: around 13 Megawatt/m
2 =
7p13 Watt per square meter (
#403), resp. 160 MW
= 8p16 Joule/sec for the whole heat shield area. At this vaporization temperature, 2000 seconds would be enough to radiate away a quantity equal to total reentry heat.
Here some relevant NASA documentations concerning the suspicious material of the Apollo heat shields:
According to [3],
Table B-3 – Normal Thermo-chemical Properties for the Apollo Heat Shield Material, density is 32 lbm/ft = 512 kg/m
3, and effective
heat of pyrolysis is 250 Btu/lbm = 0.51 MJ/kg
= 5p51 Joule per kg.
If the whole 111 kg mass loss of Apollo 4 was due to vaporization of this Apollo heat shield material, these 111 kg could have removed not even 0.06 GJ
= 7p6 Joule of total reentry heat of ~ 330 GJ
= 11p33 Joule (
#196), i.e. a portion of not even 0.02%
= 6n2.
At least the order of magnitude of the value given in [3],
Table B-3 is also confirmed by [1],
TABLE 1. – ENTHALPY OF SIX CHARRING ABLATORS AND TWO CHARS. Enthalpy resp. thermodynamic energy with respect to 0°C = 273°K has been measured for the ablative material
AVCOAT 5026/39. The highest temperate mentioned is 662°K = 389°C with an enthalpy of 0.6364 MJ/kg
≈ 5p64 Joule/kg and a mass loss of 27.5%
= n275.
I conclude that all this stuff concerning labor-intensive processes, where each individual cell of the Apollo heat shield was filled by hand with a magic material was primarily a propaganda bluff.
Quote from
NASA Applies Insights for Manufacturing of Orion Spacecraft Heat Shield, 2015:
The heat shield was composed of a titanium skeleton and carbon fiber skin that gave the crew module its circular shape on the bottom and provided structural support, on top of which a fiberglass-phenolic honeycomb structure was placed. The honeycomb structure had 320,000 tiny cells that were individually filled by hand with an ablative material called Avcoat designed to wear away as Orion returned to Earth through the atmosphere. During the labor-intensive process, each individual cell was filled by hand as part of a serial process, cured in a large oven, X-rayed and then robotically machined to meet precise thickness requirements.
However, during the manufacture of the heat shield for Orion's flight test, engineers determined that the strength of the Avcoat/honeycomb structure was below expectations.
And we all know where such
wrong expectations come from: They stem from the belief that such a technology worked without problems already more than 40 years ago.
Cheers, Wolfgang
Athletics Records on the Moon